[Help] Intel Core i7 3930K + Asus Rampage IV Extreme

[gamingpy]

@Jotole:

The voltage is not bad, there are worse ones. ;). Let's see if we can lower it a bit more. Lower it to 1.31v and do the same test as before.

The temperatures are at the limit for my taste, of course it is an H100, and passing prime, playing I doubt you will exceed 60º. Which is a more moderate temperature.

But if we are looking for the nice figure of 4.5 Ghz we have to scrape all the voltage we can. Since that H100 will limit our OC.

Salu2….

Updating to 4.3 as I know until what voltage can I lower? because as I understand it the less voltage you use the better.

[Jotole]

@gamingpy:

!

Updating to 4.3 until what voltage can I lower? because as I understand it, the less voltage you use, the better.

Wow….!!!, you're learning fast.

You have a good Proce, that voltage and frequency are already very good gamingpy.!!!!

The voltage can be lowered until the processor becomes unstable. So the more it lets you, the better. Note that now you have 300 Mhz more, and the same temperatures as at 4 Ghz.

If we want 4.5 Ghz, we will no longer lower the voltage. Try to go up to 4.5 with that voltage. If it is stable, we will lower the voltage again. When we have the voltage more or less centered for 4.5 Ghz, we will touch other values in bios.

Salu2…

[gamingpy]

I've pushed it quite a bit and I couldn't get it to 4.5ghz, in the next image I show how I increased it to 1.45 volts and without getting results I can't get it to boot, it hangs where it loads the Windows 7 logo. For fear of burning it I left it at 4.3 with 1.250 volts, what do you recommend Jotole and forum people :ugly:

[Jotole]

@gamingpy:

I've pushed it quite a bit and I couldn't get it to 4.5ghz. In the next image I show how I increased it to 1.45 volts and without getting results, I can't get it to boot, it hangs where it's loading the Windows 7 logo. For fear of burning it, I've left it at 4.3 with 1.250 volts. What do you recommend, Jotole and forum people :ugly:

!

Saludos

For 4.5, 1.45v is excessive. With the voltages you were using, you should do it at 1.30. Try it with 1.35.

Set Load Line to High.

Cpu current capability I think it was the one that was in percentages, right? I don't remember it from memory, set it to 120%.

Leave the memos to auto, it might be what's causing the problem.

[gamingpy]

Many thanks Jotole first of all for the help and for your time.

Look it doesn't work with the configuration I put below it hangs at the start of the OS. I think reaching 4.5 would be a real miracle hehe in my opinion to be the H100 as a heatsink I think 4.3 ghz is very good for it ;D

[Praimus]

Hi, I'm leaving you screenshots of how you have to put the values in bios for an OC of 4500mhz:

In CPU ratio put 45, this is the multiplier.

In CPU voltage do not put 1.49v, this is for 5ghz hehe, try with 1.35v, if it does not start go up and if it starts go down.

Leave the rest of the options that do not appear in screenshots as they come by default.

Ask any questions.

Regards.

[Jotole]

@Praimus:

Hello, here are the screenshots of how you need to set the values in the BIOS for an OC of 4500mhz:

!
!
!
! Set CPU ratio to 45, this is the multiplier.
!
!
!

For CPU voltage, do not set it to 1.49v, this is for 5ghz hehe, try with 1.35v, if it doesn't boot, increase it, if it boots, decrease it.

Leave the rest of the options that are not in the screenshots as they come by default.

Ask if you have any questions.

Best regards.

Do what Praimus tells you, and adjust the voltage as he indicates. Those screenshots sound familiar to me.. ;).

Cheers….

[gamingpy]

@Praimus:

Hello, here are the screenshots of how you need to set the values in the bios for an OC of 4500mhz:

For CPU voltage, do not put 1.49v, this is for 5ghz hehe, try with 1.35v, if it doesn't start up, keep increasing and if it does start up, keep decreasing.

Leave the rest of the options that are not in the screenshots as they come by default.

Ask if you have any questions.

Regards.

Hello Pramius, thank you very much, I will be testing it today and I will comment on it to see how it went, I also think the screenshots look familiar hehe, I think I had seen them on youtube in a similar way, regards and thanks to everyone for your help

[Praimus]

@Jotole:

Do what Praimus tells you, and adjust the voltage as indicated. Those screenshots sound familiar to me.. ;).

Best regards….

They won't sound familiar if they're yours from when you had the rampija¡¡¡ jajajjajajaja

@gamingpy:

Hello Pramius thank you very much I will be testing it today and I will comment on it to see how it went, I also think those screenshots look familiar hehe I think I had seen it on youtube in a similar way greetings and thanks to all for your help

The screenshots are from Jotole, the guy is an artist with the OC.

Best regards.

[gamingpy]

I definitely don't like the 4.5 ghz I tried it just as it shows in the screenshot and it doesn't work, it stays loading windows but never starts and what's worse it doesn't even show the operating system logo.:facepalm:

I kept increasing the voltages which I reached up to 1.45 volts and with no result at all the truth is that my case is a bit strange, but well now I'm back with the 4.3 ghz I'll have to settle for this configuration anyway thank you very much especially to Jotole and Praimus for the help and patience..

PD. I had to reinstall my OS because the tests have damaged my system boot and as I didn't want to get too involved in trying to figure out why it was damaged I loaded it back.. hehe I know it's the fastest thing to do and I did it because of the scarce time I have at the moment.

Best regards ;D

[Jotole]

@Praimus:

You won't hear them if they're yours from when you had the rampija!!! hahaha

The screenshots are from Jotole, the guy is an artist with OC.

Best regards.

Hehe, I had completely forgotten about them, besides I searched for them and as I cleaned up my phone, I couldn't find them.

It's not that big of a deal, I was also helped with the rampija ;).

Salu2…

@gamingpy:

Definitely I don't like the 4.5 ghz I tried it just as it shows in the screenshot and it doesn't work, it stays loading Windows but never starts and what's worse it doesn't even show the operating system logo.:facepalm:

I kept increasing the voltages which I reached up to 1.45 volts and without any result, to be honest it's a bit strange my case, but anyway now I'm back with the 4.3 ghz I'll have to settle with this configuration anyway, thank you very much especially to Jotole and Praimus for the help and patience..

PD. I had to reinstall my OS because the tests damaged my system boot and as I didn't want to get too involved in trying to figure out why it was damaged I loaded it back.. hehe I know it's the fastest thing to do and I did it because of the scarce time I have at the moment.

Best regards ;D

Well it's very strange that your configuration doesn't work even at 1.45. Something must be escaping. I imagine that the memory frequency is set to what it should be no?, that is, if they are 2133, they are at 2133, with their voltage.

The fact that the OS is damaged is because you must have had a "blue screen of death…..xD", right at the start of the Windows logo, it's not uncommon to happen, it has messed up some of my systems too.....xD. The perils of OC. ;).

Anyway those 4.3 are more than enough for any graphics card right now, don't worry too much and enjoy that cucumber............

Best regards..

[duozuoya]

¡Esta publicación está eliminada!

[gamingpy]

@Jotole:

Well it's very strange that this configuration doesn't work for you at 1.45. Something must be escaping. I guess you have the memory frequency set to whatever it is, right? I mean, if they are 2133, they should be at 2133, with their voltage.

If the truth be told, it is a bit strange. If I set them to 1866 mhz with their corresponding timings 9-10-9-28, what I didn't set was the voltage, which in my case would be 1.5 volts, but I don't know if that would mean much, although it could be hehejej :ugly: jaja.

@Jotole:

Anyway, those 4.3 are more than enough for any graphics card right now, don't worry too much and enjoy that cucumber............

Yes, I think for now I'll stick with these 4.3 until I try again. What seems strangest to me is that I'm not even using a stock BIOS, I've updated it and it still doesn't work, but anyway, thanks my friend.

Best regards..

[Jotole]

@gamingpy:

If the truth is a bit strange, if I set them to 1866 mhz with their corresponding timings 9-10-9-28 what I didn't put was the voltage which in my case would be 1.5 volt but I don't know if that would mean much, although it could be jejejej :ugly: jaja.

If I think that for now I'll stay with these 4.3 until I try again. What seems strangest to me is that I'm not even using a stock BIOS but I've updated it and even so it doesn't work but anyway thanks my friend.

Best regards..

Today I felt like pushing mine a bit, 5 Ghz, and memos to 2500 CL10. It would be interesting to see how far these Platinum go.!!! The processor can go lower in voltage, but in order to be able to raise the bus and consequently the memory, I need that.

Bye…

[fkb1234]

¡Esta publicación está eliminada!

[Marc1981]

Jotele, don't do that of hanging those screenshots that make our teeth long for all of us. Your processor is not normal!!!!:troll: That is not a simple 3930K if not a 3980X fortified jajajajajaja

Best regards.

[Jotole]

@Marc1981:

Jotele, don't do that of hanging those screenshots that you put on us with long teeth. Your processor is not normal!!!!:troll: That is not a simple 3930K if not a 3980X vitaminized jajajajajaja

Best regards.

Jajajajajaaa, I think more and more that Intel made a mistake in naming it….......:ugly:

Last night I botted at 5,150 and memos at 2600 with 1,50.
but it stayed at the start of Windows. I am very sure that if I put more vcore it is stable. But I am not a friend of electromigrating it.

This one has to last me a long time yet. ;).

What has me amazed are the memories, these platinum ones are at 2133, and they are at 2500. With yesterday's botting almost 500 Mhz of oc in memories is not bad, no. And that in X79 the oc to the memories is almost impossible if I caught a Z87 with these memos........;D.

A hug amic

[Marc1981]

I've tried and tried, but I can't go beyond 4.8, it's not 4.9 friendly. At 1.48V it's not stable and on cores 1 and 6 my temps skyrocket to 75 degrees. I don't see it compensating. I'll leave my configuration in case the compi wants to try. At 4.8 with 1.44V it's stable 100% with the memory at 2400mhz.

My configuration for Bios 4102

Note the values I have, the Micro and the board are water-cooled.

Extreme Tweaker

All Core Target CPU Turbo-Mode Speed : 4800MHz

Target DRAM Speed : 2400MHz

Ai Overclock Tuner: XMP
CPU Level Up: Disabled
Bclk freq: 100
CPU Strap: 100
ClockGen Full Reset: Enabled
Turbo Ratio: By all cores
By all cores : 48
CPU Clock Gen Filter: 20UF
Memory Freq: DDR3-2400
Extreme Tweaking: Enabled
EPU Power Saving Mode: Disabled

Extreme OV: Disabled
Bclk Skew: Auto
CPU Vcore : Offset Mode +
CPU Vcore V: 0.040

With this offset and the CPU LLC at High my voltage value under load is 1.44V Maximum

VTT CPU V: 1.1200
2nd VTTCPU V: Auto
CPU VCCSA manual V: 1.125
DRAM V (A, B): 1.66
DRAM V (C, D): 1.66
CPU PLL V: 1.78
PCH Voltage: Auto
VTTDR Voltage (A, B): Auto
VTTDR Voltage (C, D): Auto
CPU Spread Spectrum: Disabled
PCIe Spread Spectrum: Disabled

My memory is Corsair Dominator Platinum 4x4GB 2400CL9

Rampage Tweak : Auto

DRAM Timings

CAS: 9
RAS to CAS Delay: 11
RAS Pre time: 11
RAS ACT: 31
Command Mode: 2

Digi+ Power Control

CPU Load-Line Calibration(LLC): High
CPU current capability: 120%
CPU Voltage Freq: Manual
CPU Fixed Frecuency: Auto
VRM Over Temperature Protection: Auto
CPU Power Duty Control: T.Probe
VCore MOS Voltage Control: Auto
CPU Power Phase Control: Optimized
CPU Vcore Boot Up Voltage: Auto
VCCSA Load-Line Calibration(LLC): Regular
VCCSA Current Capability: 130%
VCCSA Fixed Freq: Auto
CPU VCCSA Boot Up Voltage: Auto
CPU VTT Switching Freq: Auto
CPU VTT Over-Current Protection: Auto
DRAM-AB Current Capability: 130%
DRAM-AB Voltage Frequency: Auto
DRAM-AB Power Phase Control: Optimized
DRAM-CD Current Capability: 130%
DRAM-CD Voltage Frequency: Auto
DRAM-CD power Phase Control: Optimized
PCH Switching Freq: Auto

Advanced Menu

CPU Configuration

Intel Adaptive Thermal Monitor: Enabled
Hyper-Threading: Enabled
Active Processor Cores: All
Limit CPUID Maximum: Disabled
Execute Disable Bit: Enabled
Hardware Prefetcher: Enabled
Adjacent Cache Line Prefetch: Enabled
DCU Streamer Prefetcher: Enabled
DCU IP Prefetcher: Enabled
Intel Virtualization Tech: Enabled

CPU Power Management Configuration

CPU Ratio: Auto
Enhanced Intel SpeedStep Technology: Enabled
Turbo Mode: Enabled
CPU C1E: Auto
CPU C3 Report: Auto
CPU C6 Report: Auto
CPU C7 Report: Auto

Here you can see the temps it takes with the voltage. But at 4.9 it's not stable. Does the program sound familiar to you?

[Jotole]

@Marc1981:

I've tried as much as I can, but I can't go beyond 4.8. It's not a friend of 4.9. At 1.48V it's not stable, and on cores 1 and 6, the temps skyrocket to 75 degrees. I don't see it compensating. I'll leave my configuration in case the friend wants to try. At 4.8 with 1.44V, it's stable 100% with the memory at 2400MHz.

My configuration for Bios 4102

! Attention to the values I have, the CPU and the motherboard are water-cooled.
! Extreme Tweaker
! All Core Target CPU Turbo-Mode Speed: 4800MHz
! Target DRAM Speed: 2400MHz
! Ai Overclock Tuner: XMP
CPU Level Up: Disabled
Bclk freq: 100
CPU Strap: 100
ClockGen Full Reset: Enabled
Turbo Ratio: By all cores
By all cores: 48
CPU Clock Gen Filter: 20UF
Memory Freq: DDR3-2400
Extreme Tweaking: Enabled
EPU Power Saving Mode: Disabled
! Extreme OV: Disabled
Bclk Skew: Auto
CPU Vcore: Offset Mode +
CPU Vcore V: 0.040
! With this offset and CPU LLC on High, my voltage value under load is 1.44V Maximum
! VTT CPU V: 1.1200
2nd VTTCPU V: Auto
CPU VCCSA manual V: 1.125
DRAM V (A, B): 1.66
DRAM V (C, D): 1.66
CPU PLL V: 1.78
PCH Voltage: Auto
VTTDR Voltage (A, B): Auto
VTTDR Voltage (C, D): Auto
CPU Spread Spectrum: Disabled
PCIe Spread Spectrum: Disabled
! My memory is Corsair Dominator Platinum 4x4GB 2400CL9
! Rampage Tweak: Auto
! DRAM Timings
! CAS: 9
RAS to CAS Delay: 11
RAS Pre time: 11
RAS ACT: 31
Command Mode: 2
! Digi+ Power Control
! CPU Load-Line Calibration(LLC): High
CPU current capability: 120%
CPU Voltage Freq: Manual
CPU Fixed Frecuency: Auto
VRM Over Temperature Protection: Auto
CPU Power Duty Control: T.Probe
VCore MOS Voltage Control: Auto
CPU Power Phase Control: Optimized
CPU Vcore Boot Up Voltage: Auto
VCCSA Load-Line Calibration(LLC): Regular
VCCSA Current Capability: 130%
VCCSA Fixed Freq: Auto
CPU VCCSA Boot Up Voltage: Auto
CPU VTT Switching Freq: Auto
CPU VTT Over-Current Protection: Auto
DRAM-AB Current Capability: 130%
DRAM-AB Voltage Frequency: Auto
DRAM-AB Power Phase Control: Optimized
DRAM-CD Current Capability: 130%
DRAM-CD Voltage Frequency: Auto
DRAM-CD power Phase Control: Optimized
PCH Switching Freq: Auto
! Advanced Menu
! CPU Configuration
! Intel Adaptive Thermal Monitor: Enabled
Hyper-Threading: Enabled
Active Processor Cores: All
Limit CPUID Maximum: Disabled
Execute Disable Bit: Enabled
Hardware Prefetcher: Enabled
Adjacent Cache Line Prefetch: Enabled
DCU Streamer Prefetcher: Enabled
DCU IP Prefetcher: Enabled
Intel Virtualization Tech: Enabled
! CPU Power Management Configuration
! CPU Ratio: Auto
Enhanced Intel SpeedStep Technology: Enabled
Turbo Mode: Enabled
CPU C1E: Auto
CPU C3 Report: Auto
CPU C6 Report: Auto
CPU C7 Report: Auto

Here you can see the temps it takes with the voltage. But at 4.9 it's not stable. Does the program sound familiar to you?

Haha, yes it sounds familiar, I don't use another. With that I control everything and it's very reliable. Mine at 5 GHz doesn't go beyond 60º, of course I have a 9 x 12 radiator for the CPU and motherboard, not much…...........xD.

From what I see in that image, you're putting 1.45 for 4.9. If you want to keep it stable, try raising it a couple more points.

Although I already told you that for an SLI of 780, which I think you have now, right? :). You have more than enough with 4.5. Pushing it further is for benchmarking, or managing 3-way or above. When gaming, you won't notice anything for those 400 MHz, and if you stress the processor too much...

Best regards

[Marc1981]

I have managed to set it to 1.48 and it is not stable either. But how can there be a 10 degree difference between one core and another? I have changed the paste 3 times, with different application methods in case it was that. But nothing stays the same. I have two triple radiators with the Scythe Gentle Typhoon at 1800. I am thinking of placing a peltier exchanger in the middle. So that the temp of the liquid goes down.