Side vents, blowing air out or drawing it in?

[Ephectx]

But the rear fan only fits one of 8 and in the front I have one of 12 in the graphics part blowing air, above, in the micro part, I have nothing, it's better this way, right?

Edit: removing the side, the temperatures have generally gone up xD

[Nemo]

Well, if there is no space, then there is no space;D... what can you do.
At the top of the case, if the case is not prepared to extract air from the top, then there is nothing you can do. But if you have the possibility to put a fan that extracts air, then it's better. The ideal thing is that fresh air enters through the bottom of the case (through the front, fans at the base of the case or sides), the fresh air circulates throughout the interior of the case and the already hot air is expelled through the top of the case (rear and top of the case). It is normal for the temperature to rise when you remove the front fan, when you introduce more cold air, you force the extraction of the hot air more, which is the weakest point of your configuration.

Best regards.

[ferelxyx]

if you have a 12 in the front and an 8 in the back, the best thing is to put the one on the side by removing
and not putting

regards

[Ephectx]

So what do I do? Do I remove both? Is it really better to put the side one out? That would leave both out, side and rear (plus the front one), wouldn't it get hotter? xD

[ferelxyx]

if you put in more air than you can take out, it gets hotter, because the hot air circulates around the box
it is better to have more taking out than putting in and that the ones taking out are as high as possible, because the
hot air always rises

regards

[Ephectx]

But, I have one in the front blowing at 12, and then the rear at 8, so do I leave the side at 12 blowing or sucking in air? I'm not sure about that.

[ferelxyx]

better to take out the 12, it lets in twice as much air as the 8 can
and it also removes the hot air from the graphics

regards

[Ephectx]

With that, would the temperatures of the processor and other components also decrease?

[Sylver]

+1 to the side shot, better to let out more air than you let in.

P.D.: The processor temperatures depend mostly on the heatsink and the thermal paste you use. The ambient temperature also influences, but less.

Regards

[Obione]

Well, that's it, +1 again at just 12s, lane 12 exiting and 12 entering. I already told you that the temperatures are good and it's not worth having one at 8 full throttle, it's killing morale xD

[Ephectx]

I haven't had time to put the side panel off, but with it on, it's not too bad, at idle they are usually "good"

General CPU (tcase): 27º
Core 1 and 2 between 28 and 42º
GPU DispIO, MemIO and Shader over 45º
Motherboard at 35º
HDD at 37º

At idle, do you see them as good? or would they be better with the side panel off?

[Franziskaner]

@Ephectx:

I haven't had time to put the side panel off, but with it on, it's not too bad, at idle they're usually "good"

General CPU (tcase): 27º
Core 1 and 2 between 28 and 42º
GPU DispIO, MemIO and Shader over 45º
Motherboard at 35º
HDD at 37º

At idle, do you see them as good? or would they be better with the side panel off?

I would try it out, after all, it's only four screws.

[defaultuser]

Well, the information in the Spoiler is for the more experienced.

! Pulling or pushing? Man, the ideal is to push and pull, laterally or frontally can vary with tastes.
! It is also interesting to have a large fan, although sometimes having a fan that is too large can be a drawback (that it does not fit, let's say).
! But for most towers, the ideal is that the air moves gently from front to back and as quietly as possible so that the cooling goes unnoticed by the neighbors.
For Ephectx, I already see many answers, and if there are more doubts, there is nothing like a photo to cut to the chase.

Salu2.

[Uhriens]

Now, it's not that hard to understand:

• priority 1: EXTRACT hot air from the case
• priority 2: BRING in fresh air into the case
• priority 3: make as little noise as possible

And that sums up, looking at your current temperatures, to:

• 12cm fan on the side blowing air out
• 12cm fan on the front bringing air in
• 8cm fan on the back at minimum RPM (and if not possible, remove it directly).

Also, temperatures appreciate a minimum of organization in the wiring, so as not to affect the air flow inside.

S2.

[edit: spelling]

[Sylver]

Uhriens man, it is preferable that the one at the back stays, so that the airflow is as straight as possible. Only with the 12 on the side, the hot air can give it many unnecessary turns inside the box, everything that is to expel hot air in the same direction that it enters, although it is a task shared, interests him.

Greetings

[Franziskaner]

the ideal solution ideal
regards.

[defaultuser]

This post is being processed/translated. The original version will be shown:

@Uhriens:

A ver, que no es tan difícil de entender:

• prioridad 1: SACAR aire caliente de la caja
• prioridad 2: METER aire fresco en la caja
• prioridad 3: que no haga excesivo ruido

Y eso se resume, viendo tus temperaturas actuales, en:

• lateral de 12 sacando aire
• frontal de 12 metiendo aire
• trasero de 8 al mínimo de revoluciones (y si no es posible, directamente quitarlo).

También las temperaturas agradecen un mínimo de organización en el cableado, para no afectar al flujo de aire del interior.

S2.

[edit: ortografía]

@defaultuser:

Bueno la informacion en el Spoiler es para los mas expertos.

! Sacando o metiendo? hombre lo ideal es metiendo y sacando , lateralmente o frontalmente puede variar con los gustos.
! Tambien es interesante tener un ______ grande, aunque a veces tener un ______ demasiado grande puede ser un inconveniente (que no quepa vamos).
! Pero para la mayoria de las _____ lo ideal es que el aire se mueva suavemente de adelante hacia detras y en lo posible de forma silenciosa para que la _________ pase inadvertida a los vecinos.

Para Ephectx ya veo muchas respuestas, y si hubiere mas dudas no hay nada como una fotito para atajar camino.

Salu2.

[Kernel1.0]

This post is being processed/translated. The original version will be shown:

Si si, primero se tiene que tener en cuenta que el flujo natural este presente y después ir metiendo más y más.

[ferelxyx]

This post is being processed/translated. The original version will be shown:

@Kernel1.0:

Si si, primero se tiene que tener en cuenta que el flujo natural este presente y después ir metiendo más y más.

eso suena algo guarro no?

jajajaja

saludos

[defaultuser]

This post is being processed/translated. The original version will be shown:

Estoy buscando unas imagenes termicas de placa completa que vi en alguna parte, pero no hay manera.