Problem with CPU cooler and high profile RAM

Lynxillo

I've only looked at the 990fx more or less through photos and at a glance it seems like they're at the same distance, thanks for the observation.
Regarding intel or amd xDD!! the pc had an AMD that I must say but waiting months, for which in the end have been the Bulldozer and specifically the FX8150… I went for 2500k because it turned out that for +/- the same performance in games, the move with intel came out cheaper for me!! Although according to many ProAMD comments, the analyzes at the moment are totally biased and the testing software don't recognize all the potential...etc, we have debate jaja.

Obione

I think you've done well, games usually don't get a lot of threads because it's complicated to program them and the teams don't get caught up trusting that they will perform in the future, I think.

Let's trust Piledriver

Chemacaso_1964

+1 dear OBI, in games multi-cores of more than four plummet, I keep waiting but for price and performance the most interesting of the FX I think is FX_6100, good OC and few W,

regards

!AMD Power!

Lynxillo

Well, here I am back with news:

EVERYTHING PERFECT! The Thermalright fits perfectly, although it has cost me a fortune to assemble it because of the thermal armor on the motherboard, etc…
With the mems in dual channel it almost touches the closest one but there is no contact.:D
Now regarding the performance, I have already gone into OC, with 4ghz on the 2500k and I have doubts/fear:

Reading the reviews of the Thermalright, and having a good ventilated case, I see the process at 72ºC average in full overclocked at 4ghz as excessive! I have a Core voltage of 1.392V max, passed through stress tests with the Linx, without failures, stable at first.
Obviously I suppose you will tell me a "What did you expect?" xD.

Lynxillo

I add that perhaps I put too much thermal paste, but not as much as the exaggerations I have seen, thin layer spread with a plastic card on the core... and the thermalright is quite tight, it doesn't move a millimeter...

Ah by the way! In IDLE it runs at 30ºC average, I also think it's a couple of degrees above what I read around...:nono:

CNCBCN

hello what did you expect? :D:D:D
no man those temps are pretty bad.
but you would have to start a little better: temps without OC at idle and at full and temps with OC at idle and at full and by the way put what you use to check the temps the stress I guess with Cpu burn ¿no? at how many RPM do you have the fan and what thermal paste have you put and some photos man don't be old-fashioned :D:D:D ah and the ambient temperature and the temp of the MB. I think with all that we can start talking

Obione

Try to relax the voltage because you are going too high for 4GHz, in fact I wouldn't go above 1.3. If it continues to have high temperatures, you will have to consider reinstalling.

Lynxillo

Well, I don't have the PC at hand from work but I'll keep you updated.
I'll try it today without OC to see how it goes. I run stress tests with Linx, and I use CPU-Z and Core temp to check. I must say that this is the first OC I've done... I've studied a lot of tutorials online.
I do remember that the MB temp is about 25ºC, the ambient temperature is about 19ºC. I've seen the HR-02 fan max out at about 1200 and a bit rpm.
The case has 4 auxiliary fans: one at the base next to the power supply that brings in air, another at the front near the HDDs that also brings in air, one at the top next to the RAM that blows air out, and one at the back next to the CPU fan that also blows air out, plus an assistant fan 50x50 on the motherboard.
It's true that the CPU voltage is a bit high when looking at OC reviews, I guess that with that voltage I should be stable at 4.5ghz... the recommended limit for air cooling is 1.4V ~ 1.42V right?
I'll play with offset, etc., to lower it and see how it performs.
I'll do all these tests this weekend and I'll let you know, and yes... CNCBCN, I'll post the photos!! xDD

Lynxillo

Well, I've returned from work, and set the factory settings. Without OC, I've done 1-hour tests with the following results:

IDLE = 34º and FULL = Oscillates from 46º to 52º with core voltage at 1.232V.

Ambient temperature 19ºC and Mb temperature at 27º constant during the tests.
I let myself be advised by experts

Nemo

The fan on the HR-02, do you have it blowing air in or blowing it out near the memos?
It seems strange to me because the latest temperatures are the same as I have with the i7 860 which is much hotter than the sandys.
You might want to reconsider the reinstallation as Obione says, with a quality paste.
Best regards

CNCBCN

in the bios how do you have the fan configured? silent, normal or "full blast" I don't know why you have it on silent and you get those temps for that, at idle I see it a bit high and at full it would be 46, throw in what you have but more … :nono:

Lynxillo