Connect the reservoir to the pump

[noninoan]

Hello, I was going to change the box if I couldn't fix the silentbox issue, but yesterday while thinking about it, I came up with the idea of adding another pump, and what you're giving me is a very good solution. Thank you very much, I'll take a closer look at it later as I have to go to work.

[noninoan]

Good afternoon, looking at the back of my box I do not see where to place the adapter you have given me, I will send you a photo.

[div][/div]

[whoololon]

Drilling.

[Espinetenbolas]

If you'll excuse me, I thought that one fitted the 120mm fan and was only for the DDC

This one works for both the D5 and the DDC and accepts multiposition (vertical and horizontal):

EK-UNI Pump Bracket (120mm FAN) Vertical – EK Webshop

Best regards

[noninoan]

So with these two things, I could put it behind the box.

EK-UNI Pump Bracket (120mm FAN) Vertical – EK Webshop
EK-XRES 100 DDC MX - Acetal – EK Webshop (I can change the reservoir for the one I have now that I think is a bit bigger)

It would be better to buy some angled fittings for the tube that comes in from behind, so it doesn't choke.

Best regards

[Espinetenbolas]

@noninoan:

So with these two things, I could put it behind the box.

Behind or inside the box as long as there is a fan or 120mm vent holes... I recommend inside to avoid moving when assembling and disassembling... this way you can put in and take out the RL in one piece without disassembling fittings.

It also avoids the hassle of bends and 90º elbows but anyway, assemble it as you see fit.

[noninoan]

Hello, my intention is to mount it behind the box where there is a 120mm fan, so I remove the silentbox and I can put the frame to put the HDDs in their place. By the way, does it cause vibrations that translate into noise when putting it behind in the fan holes? Thank you

[Espinetenbolas]

@noninoan:

Does it cause vibrations that translate into noise when you put it behind in the fan holes?

Well, the same as in any other place :troll: … obviously that pump rotates at 3000 or 4000 RPM so it generates some electrical noise and some vibrations like any turbomachine.

If your pump is PWM there is no problem for it to work normally at low RPM but if you keep it always at full speed it will be heard... it's not the noise of a compressor but if you remove the silentbox and also put it outside the box it will be heard like this:

[YOUTUBE-HD]zknWOPwhaEI[/YOUTUBE-HD]

I don't know the noise of the rest of the components and how picky you are with that but personally I wouldn't worry because the coupling kit already has rubber to absorb the vibrations.

[noninoan]

What I would also do is to put the isolation that the silentboxen carries to the support here,

EK-UNI Holder DDC V2 – EK Webshop

Tomorrow I am going to disassemble everything that needs redistribution to see if I can put it inside the box, otherwise it will have to go outside

[noninoan]

Good afternoon, in addition to ordering this adapter EK-UNI Holder DDC V2 – EK Webshop, I have also ordered this other one that you told me about EK-UNI Pump Bracket (120mm FAN) Vertical – EK Webshop, just in case I can't put it or can't find a place for it. I understand that if you put me the adapter that goes where a 12cm fan, I can put my pump with the top I have, which would be, Alphacool Laing DDC Acetal Top and the pump a Laing DDC-Pumpe 12V DDC-1T. And another thing, could I mount on a Fractal Define S the top + the pump I have, attached to this EK-XRES 100 DDC MX - Acetal – EK Webshop and using the adapter I put above that goes to the fan?

Best regards