• Portada
    • Recientes
    • Usuarios
    • Registrarse
    • Conectarse

    I have doubts about the voltage of my power supply

    Programado Fijo Cerrado Movido Hardware
    8 Mensajes 5 Posters 1.9k Visitas 1 Watching
    Cargando más mensajes
    • Más antiguo a más nuevo
    • Más nuevo a más antiguo
    • Mayor número de Votos
    Responder
    • Responder como tema
    Accede para responder
    Este tema ha sido borrado. Solo los usuarios que tengan privilegios de administración de temas pueden verlo.
    • C Desconectado
      coqueras
      Última edición por

      HELLO EVERYONE

      I wanted to know if these voltages measured from my VITSUBA SAN-70-S power supply are correct or out of range

      12.5 v
      5.5 v
      attached photo of the voltage of my power supply
      attachment_t_64777_0_fuente-2.jpg

      1 Respuesta Última respuesta Responder Citar 0
      • cobitoC Desconectado
        cobito Administrador
        Última edición por

        A ±1.8V error is accepted in the 12V channel
        The 5V has a tolerance of ±0.5V

        How did you measure them?

        Toda la actualidad en la portada de Hardlimit
        Mis cacharros

        hlbm signature

        C 1 Respuesta Última respuesta Responder Citar 0
        • C Desconectado
          coqueras @cobito
          Última edición por

          HELLO

          The way I took the measurements was with the source if it was on the motherboard, I made a bridge on the main connector and proceeded to measure with a multimeter in direct current at 20v
          In truth my question was with this voltage that I measured, could it be that the hard drives that I bought from the WD brand lasted less than a year, now I bought a SEAGATE BARRACUDA OF 2T and it has less than three months and it has noises, could it be that these voltages are causing damage to the disk? or both had bad quality

          (with load) measurement with cooler
          yellow +
          black -
          total 12.15 v

          red +
          black -
          total 5.11v

          cobitoC 1 Respuesta Última respuesta Responder Citar 0
          • cobitoC Desconectado
            cobito Administrador @coqueras
            Última edición por

            Those voltages are perfectly correct. The only thing I would try is to do a measurement under full load: connect the source to all the components of the PC, put them to work, pass some benchmark or stress test and do the same measurement again.

            Toda la actualidad en la portada de Hardlimit
            Mis cacharros

            hlbm signature

            FranziskanerF 1 Respuesta Última respuesta Responder Citar 0
            • FranziskanerF Desconectado
              Franziskaner @cobito
              Última edición por

              it could be that the FA is broken. I've looked everywhere and there's no mention of the PFC being active and for the 60 euros or so it costs, I'd rather have this one
              Corsair CX600 V2 600W Builder Series 80 Plus Bronze CP-9020048-EU Fuente
              which would give me more confidence than an Argentine company that moved to Taipei :troll:
              http://www.vitsubagroup.com/products-page/fuentes-de-poder-2/san-70-s/
              best regards
              FassouF 1 Respuesta Última respuesta Responder Citar 0
              • FassouF Desconectado
                Fassou MODERADOR @Franziskaner
                Última edición por

                If in both cases, it exceeds by half a volt the nominal value, maybe you have the Voltmeter misadjusted <:(

                Anyway, that power supply may be enough to get by, but if you value your hardware, and especially if your power needs exceed ~500w, change your power supply :sisi:

                Salu2!

                Intel i5 3570k / ASRock Z77 Extreme 4 / G.Skill F3-12800CL9D-8GBRL / Sapphire HD5850 / Samsung HD103UJ / TR TrueSpirit / NZXT Source 210 / OCZ ZS550W
                Intel i5 4570 / ASRock H87 Pro 4 / 2x G.Skill F3-14900CL8-4GBXM / Samsung 850 EVO 250Gb + ST1000DM003 + ST2000DM003 + HGST HDS723020BLA642 + Maxtor 6V250F0 / CM Seidon 240M / Zalman MS800 / CM MWE 550
                AMD Ryzen 7 1800X / B350 / 2x8GB Samsung DDR4-2400 CL17 / NVIDIA GTX 1070 8GB / SSD 120GB + ST4000DM004 + ST6000DM003 / EVGA Supernova 650 G2

                hlbm signature

                SylverS 1 Respuesta Última respuesta Responder Citar 0
                • SylverS Desconectado
                  Sylver Veteranos HL @Fassou
                  Última edición por

                  Apparently over there those sources are not bad, they compare them to Coolermaster, but I don't trust them either, and I support Fassou's recommendation… Better bad known...

                  Greetings :sisi:

                  >> i7-2600K Sandy Bridge @4.4GHz || Noctua NH-D14 || ASRock Z77 Extreme4 || 4x8Gb G.Skill Ripjaws X DDR3 1600MHz || XFX RX 5700 XT 8Gb || SSD Samsung 850 PRO 256Gb & 850 EVO 500Gb || WD Caviar Green 1Tb || Barracuda 1Tb || Corsair TX650 V2 || M-Audio Fast Track Pro || KRK RP8 RoKit G3 || BenQ GW2750 27"
                  >> Athlon 64 X2 5600+ Brisbane @2.9GHz || Gigabyte GA-M61PME-S2 || 2x2Gb DDR2 Kingston 800MHz || Sapphire Radeon HD 5850 Xtreme 1Gb || Maxtor 320Gb SATA2 || OCZ ModXStream 500W Modular || TEAC PowerMax 120/2 || Acer X243w 24"
                  >> Intel Core2Duo E6600 Conroe @2.4GHz || Asus P5N32-SLI SE DELUXE || 2x1Gb DDR2 Kingston 800MHz || Asus nVidia GeForce 9800GT 1Gb GDDR3 || Seagate Barracuda IDE 80Gb 7200RPM || Linkworld LPK12-35 450W

                  C 1 Respuesta Última respuesta Responder Citar 0
                  • C Desconectado
                    coqueras @Sylver
                    Última edición por

                    Hello

                    Thank you very much to all for the responses given, I am going to buy another source, or try another brand

                    Best regards…...

                    1 Respuesta Última respuesta Responder Citar 0
                    • 1 / 1
                    • First post
                      Last post

                    Foreros conectados [Conectados hoy]

                    0 usuarios activos (0 miembros y 0 invitados).
                    febesin, pAtO,

                    Estadísticas de Hardlimit

                    Los hardlimitianos han creado un total de 543.5k posts en 62.9k hilos.
                    Somos un total de 34.9k miembros registrados.
                    roymendez ha sido nuestro último fichaje.
                    El récord de usuarios en linea fue de 123 y se produjo el Thu Jan 15 2026.