GTX 560 Ti hot
-
hello
about the heatsink it could be for two reasons.
because you have to remove some more screws ;D
or because the thermal paste is like a rock :wall: in the second case do not pull the heatsink try to turn it slowly until it comes off, as if it were the CPU, you never remove it by pulling it always remove it by turning it a little
.
regards -
hello
about the heatsink it could be due to two things.
because you may have to remove some more screws ;D
or because the thermal paste is like a rock :wall: in the second case don't pull the heatsink try to turn it slowly until it comes off, like it would be the CPU one, which you never remove by pulling it always remove it by turning it a little
.
regardsThe most curious thing is that after having dismantled it I don't go above 80º C without changing thermal paste or anything. I will try what you say, perhaps it is like a rock. The only screws I have left are 2 of the corners that hold the connection support.
-
if you have never disassembled a graphics card, the truth is that the first time it is difficult and gives you a certain feeling, for fear of breaking something, but with care nothing happens.
I can't remember if the asus 560 is closed on both sides (top and bottom), if so it has tabs that are usually undone with toothpicks (on a gtx 280 I saw them and wished for them ;D)
be careful not to lose the thermal pads on the memos.
regards -
if you have never disassembled a graphics card, the truth is that the first time it costs and gives you a certain feeling, for fear of breaking something, but with care nothing happens.
I don't remember if the asus 560 is closed on both sides (top and bottom) if so it has tabs that are usually nullified with toothpicks (in a gtx 280 I saw them and I wished them away ;D)
be careful not to lose the thermal pads on the memos.
regardsNow you've caught me
If it's the first time you disassemble it since I have never had temperature problems with the graphics cards, so I don't exactly know what that thermal pad thing is.
I have removed all the screws except the one on the front of the connections and the result was that it moved slightly to one side and the other side was just as firm as with screws.Regards
-
remove all the screws you see ;D
the stock heatsinks and all the others (except some quality RL blocks) all make direct contact with the GPU pure none with the GPU memory modules to correct this they usually mount this
http://www.tienda-traxtore.com/tienda/index.php?page=pp_productos.php&tbusq=1&ref=ref-517&md=1
here they explain more or less how it is done and what thermal pads are
regards -
The thing is, the beeping started before disassembling it, that is, after 2 years of being mounted on the PC, last week it started beeping several random beeps, without having disassembled anything before and as I say, my graphics card was working at 70 degrees at most under full load.
Yesterday I tried to disassemble the GPU and I removed all the screws except for the two corners of the connections and it wouldn't move at all, that is, as if it were soldered in place.But it could be what I'm telling you, sometimes the connection comes loose a little and the graphics card has a beep when it doesn't have the power supply connected, it often happens that over time and when moving the cables a bit, a connection gives way a little, it seems connected but it stays a bit upwards, it's just about securing the connectors to the bottom and making them bottom out properly.
Then to remove the heatsink it's usually enough with the 4 screws at the bottom, the ones with the spring, the thermal paste dries up and it may seem like it doesn't come out but by moving it little by little to the sides it ends up coming out well, that is, if it's a standard model, custom models may have more screws.
If you find it difficult to remove the heatsink, I would take the whole graphics card to a gas station and blow compressed air into it, to blow out the dust from the fins,
regards
-
But it may be what I tell you, sometimes the connection comes loose a little and the graphics card has a beep when it doesn't have the power connected, it often happens that over time and by moving the cables a little, some connection gives way a little, it seems connected but it stays a little upwards, it's just about securing the connectors to the bottom and making them bottom out properly.
Then to remove the heatsink it's usually enough with the 4 screws at the bottom, the ones with a spring, the thermal paste dries up and maybe it seems like it doesn't come out but by moving it little by little to the sides it ends up coming out well, that is if it's a standard model, custom models may have more screws.
If you find it difficult to remove the heatsink I would take the whole graphics card to a gas station and blow compressed air into it, to blow out the dust from the fins,
regards
Nothing, there's no way. My graphics card is this one: http://www3.pny.com/font-color999999GTX-560-Ti-1024MB-PCIefont-P2961C396.aspx
I've removed all the screws and nothing. Not by rotating, not by shaking, not by throwing it against the wall (:P), it seems like a rock.
-
Learning is fun.
The reason I advise against buying GPUs from certain manufacturers is not because of the performance or the output, it's simply because the components are not of such high quality (read: Miss Pepis' heatsinks stuck on with chewing gum and Meccano parts), and sometimes because of poorly applied designs.
In my case, they almost always die from overheating, the most significant was that of a POV that had its heatsink "detached" after six months.
Just because PNY handles Quadros does not mean that the rest of their production has the same quality.
Don't waste your time with that graphics card, get rid of it, sell it while it still works, and buy one from a manufacturer that takes heat dissipation more into account. -
I wouldn't dare to disassemble a graphic card like that, I can play everything even if I have to lower some detail, besides this PNY is the same as the EVGA or all the series models, it's very normal for the heatsink to get dirty, but it's not worth spending money with how expensive the cards are and having a decent one, I would at least disassemble it and clean it and I know that in the end it's not a low-quality card, here in this video we see the Zotac and EVGA 560 and they are similar to that PNY the EVGA is the same, they are series models and they are usually manufactured by a single manufacturer, whether it's Asus or any other and the quality is the same, I see less quality components in 660 even the 670 short than that 560ti. here they show how to disassemble it.
The EVGA puts too much thermal paste, with putting a little and spreading it as thin as possible it's enough, I at least put little paste and spread it as well and as thin as possible, with a bag like the ones for garbage on a finger or a latex glove, I use my finger to spread it well and thin.
greetingsNothing, there's no way. My graphic card is this one: http://www3.pny.com/font-color999999GTX-560-Ti-1024MB-PCIefont-P2961C396.aspx
I've removed all the screws and nothing. Not even rotating, shaking, or throwing it against the wall (:P), it seems like a rock.
look at those videos I posted and I'm sure yours comes with the same screws, in the 470 and 480 if I remove the heatsink I only remove the 6 screws from the bottom of the GPU or processor but looking at the 560 Ti it seems to have many more, it all comes out as one piece, the EVGA is like yours even if it has a black PCB and yours is green, the Zotac is also the same except the casing is a bit different but it should be the same with the same screws.
-
I've removed all the screws and nothing. Not even by rotating, shaking, or throwing it against the wall (:P), it seems like a rock.
Thermal paste dries out over time and, if we also have serious temperature problems like in your case, it ends up cooking and consequently acquires more the consistency of cement than that of a putty. There is a big difference between dismantling a heatsink that has been running for months and a new one.
I strongly advise against dismantling the heatsink and I maintain my stance from the previous message.
However, if you are determined to do it, make sure not to remove a single screw, keep the equipment turned on for a good while and after turning it off, and with the card still hot, proceed to dismantle it.
Once you have made sure that the only thing keeping the heatsink attached to the card is the thermal paste, try to detach it by exerting horizontal torsion, alternating directions, and finally, with a firm blow. Do not use tools to pry it open, nor try to insert blades between the heatsink and the processor to separate it, use only your hands.
Needless to say, after cleaning it thoroughly, the most complicated part is putting it back together. Make sure, after tightening all the screws, that the board is not warped or bent, as it might not be in contact with the heatsink block at some point.
Good luck.
-
I disagree with whoololon
tin melts from 185 degrees the graph reaches 90 degrees, according to there are another 90 degrees to melt the tin but I wouldn't pull any electronic components with the tin at those temperatures (GPU and memories) that then a false contact can mean new graph :wall:
I also don't think PNY is a bad brand
disassembling a stock cooler has its work and requires time and patience (the first time I disassembled the GTX 280 it took me almost an hour to disassemble and reassemble it, after that I did it in 20 minutes)
I repeat look at the videos that Fjavi has sent you and make sure you are not leaving any screws
think that the thermal pads are adhesive and it is possible that this is what prevents you from being able to disassemble the coolerthe thermal pads
as you can see it has 10
greetings and good luck -
This post is being processed/translated. The original version will be shown:
¿Donde he hablado yo de estaño?
-
This post is being processed/translated. The original version will be shown:
¿Donde he hablado yo de estaño?
hablas de intentar desmontar la gráfica "en caliente"
saludos -
This post is being processed/translated. The original version will be shown:
Problema:
recoco
He quitado todos los tornillos y nada. Ni rotando, ni sacudiendo, ni tirandolo a la pared (:P), parece una pieda.Mi respuesta (lo voy a poner con colorines bonitos, a ver si se ve mejor):
@whoololon:La pasta termica, con el tiempo se reseca y, si además tenemos problemas serios de temperatura como en tu caso, acaba cociéndose y por consiguiente adquiere más la consistencia del cemento que de una masilla. Hay mucha diferencia entre desmontar un disipador que ha llevado marios meses funcionando y uno nuevo.
De antemano, te desaconsejo que desmontes el disipador y mantengo mi postura del mensaje anterior.
Sin embargo, si estás determinado a hacerlo, procura no quitarle ni un sólo tornillo, mantén el equipo encendido un buen rato y tras apagarlo, y con la tarjeta aún caliente, procede a desmontarla.
Cuando te hayas cerciorado de que lo único que manteiene unido el disipador a la tarjeta es la pasta térmica, intenta desprenderla ejerciendo torsión en horizontal, alternando los sentidos, y finalmente, con un golpe seco. No uses herramientas para hacer palanca, ni trates de introducir cuchillas entre el disipador y el procesador para separarlo, usa solamente tus manos.
Sobra decir que, tras limpiarlo a conciencia, lo más complicado es volver a montarlo. Asegúrate, tras volver a apretar todos los tornillos, que la placa no está combada o alabeada, ya que podría no estar en contacto con el bloque disipador en algún punto.
Suerte.
Porque de lo que se trata es de que la union entre el disipador y el resto de componentes, que posiblemente de deba al endurecimiento de la pasta termica, se debilite con el calor. Rutina cambiando disipadores.
A partir de ahí, es confundir. -
This post is being processed/translated. The original version will be shown:
Ahora me has pillado
Si es la primera vez que la desmonto dado que jamas he tenido problemas de temperatura en las graficas, asi que no sé exactamente que es eso de almohadilla termica.
He quitado todos los tornillos exceptuando el del frontal de conexiones y el resultado fue que se movia ligeramente por un lado y por el otro igual de firme que con tornillos.Saludos
¿el lado que se mueve no sera el de el PCI E ? ¿no ?
saludos -
This post is being processed/translated. The original version will be shown:
Decir que gracias a ese video en ingles he podido desmontar la gpu :fuckyea:
Cuando estoy echando la pasta noctua… y resulta que me quedaba casi nada. ¿Que pasta me recomendais para maximizar el contacto y refrigeracion? Yo iba a usar la que me venia con el refrigerador cpu Noctua, la NH-1. ¿Alguna mejor?
Lo de las almohadillas termica no serian los adhesivos termicos cuadrados?
-
This post is being processed/translated. The original version will be shown:
pues me alegro mucho ¿ que te faltaba por quitar?
yo en pastas siempre uso la misma arctic MX-4
http://www.tienda-traxtore.com/tienda/index.php?page=pp_producto.php&md=0&ref=VEN642
relación calidad/cantidad/precio esta muy bien
es vieja de cojones pero es bastante completita
80-way Thermal Interface Material Performance Test | Thermal Interface Material,Thermal Paste,Heatsink Compound,80-Way Thermal Interface Material Best Thermal Paste Heatsink Compound Cooling Performance Comparison Benchmark Tests
mira y compara ;D
P.D intenta no mezclar dos tipos de pasta ;D
saludos -
This post is being processed/translated. The original version will be shown:
pues me alegro mucho ¿ que te faltaba por quitar?
yo en pastas siempre uso la misma arctic MX-4
MASILLA ARCTIC MX-4 4gr.
relación calidad/cantidad/precio esta muy bien
es vieja de cojones pero es bastante completita
80-way Thermal Interface Material Performance Test | Thermal Interface Material,Thermal Paste,Heatsink Compound,80-Way Thermal Interface Material Best Thermal Paste Heatsink Compound Cooling Performance Comparison Benchmark Tests
mira y compara ;D
P.D intenta no mezclar dos tipos de pasta ;D
saludosQuitar el frontal metalico. Digo, las almohadillas termicas que mencionabais son esos adhesivos cuadrados de color gris?
No hay ningun problema en usar una pasta diferente en la cpu y otra en la gpu no?
-
This post is being processed/translated. The original version will be shown:
Quitar el frontal metalico. Digo, las almohadillas termicas que mencionabais son esos adhesivos cuadrados de color gris?
si los que marque con flechas en la foto
saludos -
This post is being processed/translated. The original version will be shown:
si los que marque con flechas en la foto
saludosVale, pues nada, cuando vuelva de vacaciones el viernes ire a comprar la pasta termica, se la aplicaré y a que se seque. ¿Cuando tarda en secar y acomodarse co la mx-4?
