Test of the Real Nvidia Gtx Titan, single-sli-tri Sli, 4 WAY SLI
-
Finally, both graphics cards have been flashed with the skynet rev2 bios. I finally took the risk!
I have the stock bios saved just in case.These bios run at 1006Mhz by default and with boost removed, I think that's what they're meant for.
At most, I'll overclock them to 1100 Mhz if I can increase the voltage with the Evga Precision.I just checked in Grid 2 that the Zotac runs at 1.20v and the Asus runs at 1.16V, I suppose it's because of the ASIC. Is that normal?
The Evga Precision has the default valuesSoon I'll put the Asus with an EK block, it reaches 70º with the stock cooler
The 3 radiator of 240mm seems a bit exaggerated to me for graphics and I7 3930K at 4.4Ghz, I'll see what you recommend here.
Jotele I think told me that it's a bit tight for this equipment, I'm having doubts about what to do.
Thanks to all of you for your valuable help, guys!Regards
If it must be normal that the one with the worst ASIC needs more voltage, there's a big difference in ASICs, that should be marked for each chip, I don't think that's a bios thing, that's why each one probably has a different boost, for sure with the original bios the Asus would reach a higher frequency.
My 780 although it says boost 1006, it actually reaches 1124mhz, in games that require a significant load it sets itself to that frequency, it's like an automatic OC that sets the frequency according to what that GPU can handle.
Regards
-
Raising it a bit to 1150 makes the graphics explode, reaching 87º and the fan at 95% and it restarts, if I leave it at 1006 with the same temperatures nothing happens to me.
Is it due to the temperatures, lack of power from the source?
What do you think, in winter it didn't happen to me, of course it was at 75º and 75 fan and I had no problems at 1215 or will it depend on the game in question.-
Greetings.-
-
Boosting it a little to 1150 makes the graphics explode, reaching 87º and the fan at 95% and it restarts, if I leave it at 1006 with the same temperatures nothing happens.
Is it because of the temperatures, lack of power from the power supply?
What do you think, in winter it didn't happen, of course it was at 75º and 75 fan and I had no problems at 1215 or will it depend on the game in question.-
Regards.-
I don't think that power supply lacks power, which one is it, the 1 rail or the 4 rail? if one of those 4 rail ones could handle my 295, maybe it's that your graphics card doesn't go up much and if you also use high resolution it's normal that it gets hot and ends up exploding, look especially at the VRM to see what temperature it reaches, you will have to ventilate the tower better.
My 780 so far heats up very little, I have a fan profile, it's just a habit but even with the new Splinter cell I didn't see it go over 60º, not even with Crysis 3 although I don't play for long periods but it usually stays pretty cool always.
regards
-
¡Esta publicación está eliminada! -
I don't think that the power supply lacks power, which one is it, the 1-rail or the 4-rail? If one of those 4-rail ones could handle my 295, maybe it's that your graphics card doesn't go up much and if you also use normal high resolution it gets hot and ends up frying, look especially at the VRM to see what temperature it reaches, you'll have to ventilate the tower better.
My 780 so far gets very little heat, I have a fan profile, it's just a habit but even with the new Splinter cell I didn't see it go over 60º, not even with Crysis 3 although I don't play for very long but it usually stays pretty cool always.
regards
I would think that for power supply power it wouldn't be the 4-rail either, it's probably already at the output the same as the tower, I agree with you about Batman when he applies physics with the gloves it automatically drops 8-12 fps reaching 30-40 fps, so I'll put the gtx 580 for physx.
regards.-
-
I would think that due to source power it wouldn't be 4-lane either, it's already out the door, same as the tower, I agree with you about Batman when he applies physics with the gloves, it automatically drops to 8-12 fps and goes down to 30-40 fps, so I'll put the gtx 580 for physx.
Regards.
With the 580 you can use it at least for Batman, they always have demanding areas especially because of the physics, a dedicated one will help.
Although then the source will already be a bit tight, in any case for physics the 580 will consume less.
regards
-
Xenxo sorry for not replying before but I've been away and tomorrow I'll be out again in the afternoon as I don't work in Spain and now we have a lot of work. With those radiators you have more than enough. I would advise you to flash the bios of the evga hydrocopper as it is a super secure bios and it goes up to 1150Mhz without touching anything, at least mine do. Flashing has its risks but it's very simple, I advise you not to go crazy with cd or usb bootable in MS-DOS and use the nvflash version of Windows, it shouldn't fail you
-
With the 580 you can use it at least for Batman, they always have demanding areas especially for physics, a dedicated one will help.
Although then the power supply will already be a bit tight, anyway for physics the 580 will consume less.
regards
The power supply is from the old days and I couldn't put 2 graphics cards of 8+6, so I just returned from a store that opens on Sundays and updated
Mouse Razer Mamba (the Logitech died a few days ago and I was using a generic one)
Tower Thermaltake Level 10 GT
Power supply Thermaltake Smart M1200W plus bronze efficiency 82-88 (generally from what I read 85) I would have liked a platinum but this one is for dummies ;D who don't want to bother with cables.
And I bought a rarity for me that I saw in the store Thermaltake Cyclo Slot Fan (I'll try to see if it reduces the temperature to the graphics card before changing the tower) I knew about the Antec Vcool that it lowered 5ºC, so for 7 Euros I couldn't resist.
regards.
-
The power supply is from the old and I couldn't put 2 graphics cards of 8+6, so I just returned from a store that opens on Sundays and updated
Mouse Razer Mamba (the Logitech died a few days ago and I was using a generic one)
Tower Thermaltake Level 10 GT
Power supply Thermaltake Smart M1200W plus bronze efficiency 82-88 (generally 85 according to what I read) I would have liked a platinum one but this one is for dummies ;D who don't want to deal with cables.
And I bought a rarity for me that I saw in the store Thermaltake Cyclo Slot Fan (I'll try to see if it reduces the temperature to the graphics card before changing the tower) I knew about the Antec Vcool that it lowered 5ºC, so for 7 Euros I couldn't resist.
Regards.
How fast you are… you won't have a power supply problem anymore, I remember having one of those heat extractors a few years ago with the G80s and it gave me very good results, I had a very bad case and just putting the 8800 it got to 80ºC without playing, I did that fix with the extractors and I managed to lower the temperature to 62ºC.
Curiously, even though that card is so hot it still works and that's with a pretty significant OC, but I haven't needed to put it in the oven or anything, it's going well although it's already very short, my sister has it, but they only play Angry Birds, they don't need more.
Well, my 780 has failed for the first time, the OC has failed, I was running Valley at 1293 and 450 memory and it was spitting out quite a few frames but suddenly the screen went black and continued but at the factory frequency, the first time I've seen a failure like this, normally the driver would fail but you can tell either it has low voltage or it exceeds 105% of the power target.
Regards
-
Xenxo sorry I didn't reply before but I've been away and tomorrow I'll be out again in the afternoon since I don't work in Spain and now we have a lot of work. With those radiators you have more than enough. I would advise you to flash the bios of the evga hydrocooper since it's a super safe bios and it goes up to 1150Mhz without touching anything, at least mine do. Flashing has its risks but it's very simple, I advise you not to go crazy with cd or usb bootable in MS-DOS and use the nvflash version for Windows, it shouldn't fail you
A colleague from N3D sent me the bios of skynet v2 and it works in pm and goes 1008 MHz and it works for me in pm
Could you send me the bios you mentioned in private
I won't put another radiator
Thanks for your helpSent from my GT-N7100 using Tapatalk
-
Here it is, original evga hydrocooper: -
How fast you are… you certainly won't have a power supply problem, I remember having that heat extractor a few years ago with the G80s and it gave me very good results, it had a very bad case and just putting the 8800 it got to 80º without playing, I did that fix with the extractors and I managed to lower the temperature to 62º.
Curiously, as hot as that card is, it still works and I was pushing a pretty significant OC, but I haven't needed to put it in the oven or anything, it's going well although it's already quite short, my sister has it, but they only play Angry Birds, they don't need more.
Well, my 780 has failed for the first time, the OC has failed, I was running Valley at 1293 and 450 memory and it was spitting out quite a few frames but suddenly the screen went black and continued but at the factory frequency, the first time I've seen such a failure, normally the driver would fail but you can tell either it has low voltage or it exceeds 105% of the power target.
regards
After doing the tests, the fan slot cooler attached to the Titan lowers it by 2ºC, I'm not sure if I should leave it a slot of space, the failure is probably the power target in some cases it reaches 128, I have it at 130º and 89º of GPU.
Well not fast, I've been turning the tower over for over a year and the power supply for 6 months but they are purchases that will last for a long time.
regards.
-
I've done the tests and the fan slot cooler attached to the Titan is 2ºC cooler. I'm not sure if I should leave a slot of space. The failure is probably the power target. In some cases it reaches 128. I have it set to 130º and 89º GPU.
Well, it's not quick, I've been messing around with the tower for over a year and the power supply for 6 months, but these are purchases that will last for a long time.
Regards.
I already imagined it must be the power target. It's a shame because it looked stable without artifacts or stuttering, although I passed half the test at factory frequency and it gave me the best score.
I can't see the BIOS for my card. They've put the WF3 but it's different from mine and also the WF that has issues with the voltage. Let's see if they put the one from the WF rv2. If I can put a little more voltage and raise the power target, this card will overclock well. I'm getting more and more frustrated with this boost, because in the end it limits you.
Although for those who don't OC it's good because it automatically sets to 1124mhz and it's an extra in performance. If the game doesn't require much load, it lowers the frequency and voltage to maintain stable 60 fps.
regards
-
Testing the cyclo slot fan went from 87ºC and 95% fan to 84ºC and 90% an improvement not substantial but it's an improvement after all
When changing the pass tower to 78ºC and 81% adding a 120mm cooler on the bottom I will test trying to add a 140mm attached to the rigid ones.
Ambient temperature 25ºC, in this case the cyclo slot fan fails to improve the temperature.
Well we are already ready to test the GTX 580 for physx, leaving one PCI at 8X but the 2 graphics cards would be stuck or a PCI at 4X leaving distance between both.
You will notice in the performance the 8X against the 4X
? -
Testing the cyclo slot fan went from 87ºC and 95% fan to 84ºC and 90% an improvement not substantial but it's an improvement
When I changed the tower it went to 78ºC and 81% adding a 120mm cooler on the bottom I will try adding a 140mm attached to the rigid ones.
Ambient temperature 25ºC, in this case the cyclo slot fan doesn't manage to improve the temperature.
Well we are ready to test the GTX 580 for physx, leaving one PCI at 8X but the 2 graphics cards would be stuck or a PCI at 4X leaving distance between both.
You will notice the performance difference between 8X and 4X
?The thing is that if you put the physics one at 8x and the main one also at 8x I would prefer the Titan at 16x and the 580 at 4x, I don't think there's much difference between 4x and 8x in a card for physics, and if with 4x you have more space between them then it's better.
regards
-
The thing is, if you set the physics one to 8x and the main one stays at 8x as well, I'd at least prefer the Titan at 16x and the 580 at 4x, I don't think there's much difference between 4x and 8x on a card for physics, and if with 4x it's more separated then even better.
regards
I hadn't gone into that detail in SLI configuration if I knew they stayed at 8X/8X but I didn't know that the same thing happened with different graphics.
Well then, let's try it on the 4x pci.
Thanks.
-
I hadn't gone into that detail about SLI settings. I knew they stayed at 8X/8X, but I didn't know the same thing happened with different graphics cards.
Well, then I'll try it on the 4x PCI slot.
Thanks.
That has nothing to do with SLI or CF. If you plug in two cards, it goes to 8x8. If it were an x58, x79, then they would go to 16 or 16x8x8. That's the limitation Intel puts on those chipsets. If you don't have a PLX, it would limit you even with a sound card, I mean if you connect it to a PCIe x16.
It's about time Intel gave those chipsets a 16x16, but they don't feel like it because they have no competition.
Intel does whatever it wants. If they put a 16x16 on the Z87, they wouldn't sell a single x79, or they would sell very few, since both Z77 and Z87 are better, I'm talking about gaming performance. Even though a Z87 would allow an 8x8x8x8, it would still have a clear advantage in a 4way SLI of 780, because in addition to PCIe3, it would have a better PCIe controller, it's like the memory controller that improves with each new CPU series and frequencies, it will be similar.
With Z77 I'm referring to Ivy, that is 3xx0K, and Z87 to 4xx0K.
regards
-
Hello ELP3…
I just got myself a couple of 290x cards and I can unlock voltage..
Put your best bench with the titans in sli there, I'm going to run over you...
I'll look back at you in the rearview mirror, hehe...
-
Hello ELP3…
I just got a couple of 290x bichas and I can unlock voltage..
Put your best bench there with the titans in sli, I'm going to go over you...
I'll see you in the rearview mirror, hehe...
Well you already have courage..
Good luck. I think you're going to need it hehe
Look for the post of the 780Ti I think my results are there..they can always be improved. For example the 3DMark we know runs much better on Win 8, but I'm not installing that OS on my computer for now..it gives me the creeps..hehe
However, more than against me, since I'm ahead with overvolting, I think it would be fairer for you to compare with ConanR since he's on the same conditions. Unless you've messed it up..and don't remove tessellation eh? we don't know everything here…hehe
A hug..and good luck..;)
-
Well, you already have courage..
Good luck. I think you'll need it hehe
Look for the post about the 780Ti, I think my results are there..they can always be improved. For example, we all know that 3DMark runs much better on Win 8, but I haven't installed that OS on my computer yet..it gives me the creeps..hehe
However, rather than against me, since I have an overclocking advantage, I think it would be fairer for you to compare with ConanR since he's on the same conditions. Unless you've messed it up..and don't remove tessellation eh? we don't know everything here…hehe
Take care..and good luck..;)
Elpe..
I'm serious. Put your best bench in sli, I'll beat it for sure... It's not a joke... I have a 290 terminator... They wipe out everything, even your vitaminized titan sli...
