MB Asus p8b75 MLX-PLUS, it came out on the MB TEMp -63 degrees and then …

[alejotok]

I have an Asus P8b75 MLX-PLUs MB: micro Dual Core G2020 vel 2.9 and GSkill 1866 ram, note that it only takes 1333. and an nvidia 9500 GT video card..now…
A week ago it showed me the Aus Suite Tool from asus to monitor the pc...
that the MB temperature was -63 degrees C and -81 degrees F...I kept working and yesterday...working in After Effect, I felt it was slow..and I turned it off for a while...when I turned it on again, it had a sign that the Asus Surge from the board went up...because of the voltage and it shows me this image...IMAGE 1...I disconnected it and changed the power supply that mine is not very good...for another and it was still the same....I removed all devices, left it only with the keyboard and monitor......and it gave me this...
IMAGE 2...
WHAT COULD HAVE HAPPENED?.....GREETINGS TO ALL!!!...AND HELP ME PLEASE...

[Fassou]

A negative temperature is usually a symptom that the probe is damaged, but as you explain it like a closed book, it is difficult to tell.

Salu2!

[alejotok]

And that is solvable… what else can it be.... another question could be a high or low voltage of the current..... or humidity?

[Sylver]

1.-Damaged probe.
2.-Bad explanation.
3.-Write with a capital letter in the first letter of all words

Check that, let's see if we can help you more later :sisi:

Regards

[alejotok]

I have an Asus P8b75 MLX-PLUs motherboard: dual core G2020 micro vel 2.9 and GSkill 1866 ram, note that it only takes 1333. and an nvidia 9500 GT video card..now…THE POWER SUPPLY IS BAD..I THINK THE BRAND IS EUROPE ELECTRI SOMETHING LIKE THAT...WELL THE CASE IS THAT...
A week ago it showed me the Aus Suite Tool from asus to monitor the pc...
that the temperature of the MB was -63 degrees C and -81 degrees F..NOTE...-63 NOT +63.....AND IT SHOWED IT TO ME IN THE SETUP.....I kept working and yesterday...working in After Effect, I felt it slow..and I turned it off for a while...when I turned it on again,, IT REbooted AND had a sign (Power supply surges detected during the previous power on. Asus Anti-Surge was triggered to protect system from unstable power supply unit!)..
and
the voltage values were like this!!..
Cpu Voltage +0.992 v
3.3v Voltage +3.376 v
5v Voltage +5.763 v ** IN RED**
12v Voltage +12.288

and above in the temperature it stayed fixed:
MB Temperature -63degrees C / -81Grados F

I turned it off, disconnected the video card and everything...I only connected the keyboard(PC2) and the monitor..removed HDD and everything.....and reset the bios, removing the battery....and I changed the power supply to another one that is not very good either, it is 550w 2A...and the values became like this...
Cpu Voltage +0.984 v
3.3v Voltage +3.376 v
5v Voltage +5.461 v without being in red
12v Voltage +12.288.....
and I no longer get the Anti Surge sign...but I do not want to use it because I do not know if I damaged it or not...what do you suggest I do.......GREETINGS AND PLEASE HELP ME!!!..THANK YOU!!

[Fassou]

@Sylver:

3.-Escribir con mayúscula en la primera letra de todas las palabras

That's what VBulletin does, when you write everything in uppercase ¬¬

In summary, you had a very bad font, as expected it ended up messing you up, and you ruined the sensor of the board.

If you have learned the lesson, you will put a reliable and decent font and evaluate possible damage to the rest of the components, or you will put another one that is just as bad, and let the party continue.

Salu2!

[packosoft]

as you have been told, little more than changing the font for a decent one and praying that the broken part is just the temperature probe

[alejotok]

Today I measured the voltage that the power supply is giving and it is correct…5.130 to 5.200 and the usb of the board...and also...it seems that the temperature sensors are broken...because the current that the power supply gives is correct and the one that is on the board is also correct....what do you think...regards!!!